SECTION 9T1
REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
Caution : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
SPECIFICATIONS
Fastener Tightening Specifications
Application
|
N•m
|
Lb-Ft
|
Lb-In
|
|
Siren Braket Mounting Bolts.
|
8
|
-
|
71
|
SCHEMATIC AND ROUTING DIAGRAMS
Remote Keyless Entry and Anti-Theft System (Notchback)
Remote Keyless Entry and Anti-Theft System (Hatchback)
Remote Keyless Entry and Anti-Theft System (Station Wagon)
Control Module/Receiver Connector
Terminal
|
Color
|
Description
|
|
1
|
YEL
|
Siren
|
|
2
|
BLK
|
Ground
|
|
3
|
-
|
-
|
|
4
|
LT BLU
|
Trunk/Tailgate Tamper Switch
|
|
5
|
PNK/BLK
|
Trunk/Tailgate Open Switch
|
|
6
|
-
|
-
|
|
7
|
PNK/DKBLU
|
Hood Open Switch
|
|
8
|
PPL
|
Door contact Switch
|
|
9
|
LT BLU/BLK
|
Door Lock Monitoring
|
|
10
|
LT GRN/WHT
|
Lock
|
|
11
|
YEL
|
Unlock
|
|
12
|
LT GRN
|
Driver Key Cylinder Unlock Switch
|
|
13
|
DK BLU
|
Right Turn Signal Bulb
|
|
14
|
-
|
-
|
|
15
|
PNK
|
Ignition Switch
|
|
16
|
-
|
-
|
|
17
|
LT GRN
|
Diagnostic Communication
|
|
18
|
LT GRN/RED
|
Key Reminder Switch
|
|
19
|
YEL/DK GRN
|
Security Indicator
|
|
20
|
PPL
|
Passenger Key Cylinder Unlock Switch
|
|
21
|
-
|
-
|
|
22
|
-
|
-
|
|
23
|
-
|
-
|
|
24
|
BRN
|
Trunk Open Switch
|
|
25
|
ORN
|
Battery+
|
|
26
|
LT BLU
|
Left Turn Signal Bulb
|
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
Control Module/Receiver
Removal Procedure
- Disconnect the negative battery cable.
- Remove the floor console. Refer to Section 9G, Interior Trim.
- Disconnect the control module/receiver electrical connector.
- Slide the control module/receiver away from its mounting bracket.
Installation Procedure
- Install the control module/receiver on its mounting bracket.
- Connect the control module/receiver electrical connector.
- Install the floor console. Refer to Section 9G, Interior Trim.
- Connect the negative battery cable.
Siren
Removal Procedure
- Remove the siren electrical connector.
- Remove the siren bracket mounting bolts and siren.
Installation Procedure
- Install the siren with the mounting bolts.
Tighten
Tighten the siren braket mounting bolts to 8 N•m (71 lb-in).
- Connect the siren electrical connector.
Hood Open Switch
Removal Procedure
- Disconnect the negative battery cable.
- Disconnect the hood open switch connector.
- Remove the clip and hood open switch.
Installation Procedure
- Install the hood open switch and clip.
- Connect the hood open switch connector.
- Connect the negative battery cable.
Hatchback Tailgate Tamper Switch
(NOTCHBACK, STATION WAGON SIMILAR)
Removal Procedure
- Disconnect the negative battery cable.
- Disconnect the tailgate tamper switch connector.
- Remove the screw and tailgate tamper switch.
Installation Procedure
- Install the tailgate tamper switch and screw.
- Connect the tailgate tamper switch connector.
- Connect the negative battery cable.
Remote Keyless Entry Transmitter Programming
The Remote Keyless Entry System allows for the use of as many as four(4) transmitters for each vehicle. Replacement Remote Keyless Entry System Transmitters must first be programmed to specific vehicle using the Secan tool.
This process is completed using serial data communication between the Scan tool and the Remote Keyless Entry Control Unit and is the only method available for programming Transmitters.
Notice : All Transmitters for a specific vehicle must be programmed at same time.
Notice : Once the programming function of the Remote Keyless Entry System is activated, any Transmitter(existing or new) that is not programmed(or reprogrammed) during the programming procedure will no longer operate the Remote Keyless Entry System of that vehicle.
Notice : Ensure that the doors, hood and trunk/tailgate hatch are closed prior to starting the programming procedure.
Caution : Ensure that Transmitters from other vehicles in the immediate area are not activated during programming procedure.
Caution : Turn the ignition to ON before installing in the scan tool. Failure to connect in this procedure may cause communication errors and the programming procedure will not complete. Any keys that are not programmed at this time will no longer function.
- Turn ON the ignition, with the engine OFF.
- Install the scan tool.
- Select PROGRAMMING KEY FOBS from the BODY menu.
- Follow the scan tool instruction with each key until all keys are programmed.
- Turn the ignition to the LOCK position, disconnect the Tech 2 and test all the keys.
GENERAL DESCRIPTION AND SYSTEM OPERATION
Remote Keyless Entry and Anti-Theft System
The remote keyless entry and anti-theft system can perform the following functions:
- Remotely lock and unlock the vehicle doors by means of a hand-held, high-frequency transmitter.
- Sense intrusion into the vehicle.
- Activate a warning in the event of an intrusion.
- Activate a warning when the PANIC button is pressed.(Hatchback, Station Wagon only)
- Help the driver find the vehicle in a parking area.
- Automatically re-lock the doors if the door or the trunk/tailgate is not opened within 30 seconds after the vehicle has been unlocked by the remote keyless entry.
- Communicate serial data to a scan tool to help diagnose system faults.
The remote keyless entry and anti-theft system consists of the following components:
- Keyless entry and anti-theft control module/receiver.
- Hand-held transmitter.
- Security indicator.
- Trunk/tailgate open switch.
- Trunk/tailgate tamper switch.
- Front door tamper switches.
- Door contact switches.
- Central door lock relay.
- Turn signal bulbs.
- Siren.
- Hood open switch.
Remote Locking and Unlocking
The hand-held transmitter locks and unlocks the vehicle doors by sending radio waves to the control module/receiver in the vehicle. The effective range of the transmitter varies between 5 and 10 meters, (approximately 16 to 32 feet), depending on whether or not objects, such as other vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK button which only function when the ignition is OFF. Pressing the UNLOCK button has the following effects:
- The doors are unlocked.
- The turn signal bulbs flash twice.
- The control module is disarmed.
Pressing the LOCK button has the following effects:
- The doors are locked.
- The turn signal bulbs flash once.
- The horn chirps once.
- The control module is armed.
The transmitter has a replaceable battery. The battery is designed to last at least two years before replacement is necessary.
Security Indicator
There is a security indicator on the driver's door lock button cover. After the LOCK button of the transmitter is pressed, the module is placed in the armed mode, and the security indicator flashes. The security indicator turns ON for 0.1 seconds and OFF for 0.7 seconds. It then flashes at that frequency until the control module/receiver is disarmed.
Intrusion Sensing
The anti-theft function is armed if the transmitter sends the LOCK message to the control module/receiver when the ignition is OFF. When the hood, door, or trunk/tailgate is opened, the hood open, door contact, or trunk/tailgate open switch sends a "ground" signal to the control module/receiver. Unless the control module/receiver is disarmed, the siren will be activated when the "ground" signal is received from the trunk/tailgate open, hood open, or door contact switches.
The following actions disarm the anti-theft system:
- An UNLOCK message is received from the transmitter.
- Key operation is detected by the tamper switches. (The tamper switches are operated by the lock cylinders in the front doors and trunk/tailgate.)
The alarm will also be activated if the control module/receiver detects voltage from the ignition before either of the following conditions occur:
- An UNLOCK message is received from the transmitter.
- Key operation is indicated by the tamper switches.
Siren (General Only)
The remote keyless entry system is armed when the LOCK message is received from the transmitter when the ignition is OFF. When the system is armed, it will activate the siren and flash the turn signals for 28 seconds if any of the following conditions occur:
- A door is opened without using the key before an UNLOCK signal is received from the transmitter.
- The rear deck lid is opened without using the key before an UNLOCK signal is received from the transmitter.
- The hood is opened before an UNLOCK signal is received from the transmitter and before a door or the rear deck lid is unlocked.
- The ignition switch input indicates battery voltage before either a key is used to unlock the vehicle or an UNLOCK signal is received from the transmitter.
The siren will not operate if any of the following conditions occur after the system has been armed:
- The door is opened with the key.
- The trunk/tailgate is opened with the key.
- The UNLOCK or LOCK button on the remote transmitter is pressed.
Vehicle Locator
The remote keyless entry system assists the driver in locating the vehicle. When the vehicle is unlocked with the remote control, the turn signals flash twice to indicate the location of the vehicle. The duration of the flashes and the length of time between flashes is used to indicate certain vehicle conditions. Refer to
"Fault or Alarm Indication"
in this section.
Autolocking (Safety Lock)
The remote keyless entry system features an autolocking feature. If the doors are unlocked with the remote transmitter when the control module/receiver is in the armed mode, the doors are automatically re-locked after 30 seconds unless any of the following events occur:
- A door is opened.
- The ignition is ON.
- The trunk/tailgate is opened.
- The hood is opened.
Panic
(HATCHBACK, STATION WAGON ONLY)
The remote keyless entry System will activate the siren and flash the turn signals when the PANIC message is received from the transmitter when the ignition is OFF.
A press of the PANIC button for 0.5 seconds performs the following functions:
- The turn signal lamps flash for 0.25 seconds, with a 0.25 seconds pause between flashes.
- The siren is pulsed.
All of the above will continue for 28 seconds or until the PANIC button is pressed again.
Fault or Alarm Indication
When the UNLOCK button on the remote transmitter is pressed, the control module/receiver will flash the turn signal lamps to indicate information about the remote keyless entry and anti-theft system.
Normal Condition: If there has not been an intrusion, and no fault has been detected, the control module/receiver will signal a normal condition when the UNLOCK button is pressed. The turn signal lamps will flash twice for 0.5 seconds, with a 0.5 seconds pause between flashes.
Alarm Indication: If there has been an intrusion since the last time the LOCK button was pressed, the control module/receiver will signal that there has been an intrusion when the UNLOCK button is pressed. The turn signal lamps will flash twice for 0.5 seconds, with a 1.5 seconds pause between flashes.
Alarm and fault information will be erased the next time the transmitter arms the control module/receiver by transmitting a LOCK message.
Control Module/Receiver
The remote keyless entry control module/receiver is contained in the floor console. The module/receiver processes signals from the remote transmitter and various switches. It activates the alarm if an intrusion is detected. The control module/receiver also has a self-diagnostic function which will display trouble codes. In order to display trouble codes, a scan tool must be connected to the data link connector (DLC).
The control module/receiver will not communicate with transmitters from other vehicles because there are over four billion possible electronic password combinations. It is highly unlikely that any transmitters will use the same password. The control module/receiver has an attached antenna to detect signals from the transmitter.
